- September 11, 2015
- Posted by: Syed Shujaat
- Category: Cisco
No Comments
| access-enable Create a temporary Access-List entry |
| access-profile Apply user-profile to interface |
| access-template Create a temporary Access-List entry |
| archive manage archive files |
| auto Exec level Automation |
| beep Blocks Extensible Exchange Protocol commands |
| bert Bit Error Rate Testing |
| bfe For manual emergency modes setting |
| calendar Manage the hardware calendar |
| cd Change current directory |
| cellular cellular commands |
| clear Reset functions |
| clock Manage the system clock |
| cns CNS agents |
| configure Enter configuration mode |
| connect Open a terminal connection |
| copy Copy from one file to another |
| crypto Encryption related commands. |
| ct-isdn Run an ISDN component test command |
| debug Debugging functions (see also ‘undebug’) |
| delete Delete a file |
| dir List files on a filesystem |
| disable Turn off privileged commands |
| disconnect Disconnect an existing network connection |
| dot11 IEEE 802.11 commands |
| dot1x IEEE 802.1X Exec Commands |
| enable Turn on privileged commands |
| eou EAPoUDP |
| erase Erase a filesystem |
| ethernet Ethernet parameters |
| event Event related commands |
| exit Exit from the EXEC |
| format Format a filesystem |
| fsck Fsck a filesystem |
| help Description of the interactive help system |
| hms Host Mapper Service |
| isdn Run an ISDN EXEC command on an ISDN interface |
| lock Lock the terminal |
| login Log in as a particular user |
| logout Exit from the EXEC |
| microcode microcode commands |
| mkdir Create new directory |
| modemui Start a modem-like user interface |
| monitor Monitoring different system events |
| more Display the contents of a file |
| mpls MPLS commands |
| mpoa MPOA exec commands |
| mrinfo Request neighbor and version information from a multicast |
| router |
| mrm IP Multicast Routing Monitor Test |
| mstat Show statistics after multiple multicast traceroutes |
| mtrace Trace reverse multicast path from destination to source |
| name-connection Name an existing network connection |
| no Disable debugging functions |
| pad Open a X.29 PAD connection |
| partition Partition disk |
| ping Send echo messages |
| ppp Start IETF Point-to-Point Protocol (PPP) |
| pwd Display current working directory |
| radius radius exec commands |
| redundancy Redundancy Facility (RF) exec commands |
| release Release a resource |
| reload Halt and perform a cold restart |
| rename Rename a file |
| renew Renew a resource |
| restart Restart Connection |
| resume Resume an active network connection |
| rlogin Open an rlogin connection |
| rmdir Remove existing directory |
| rsh Execute a remote command |
| send Send a message to other tty lines |
| set Set system parameter (not config) |
| setup Run the SETUP command facility |
| show Show running system information |
| slip Start Serial-line IP (SLIP) |
| ssh Open a secure shell client connection |
| start-chat Start a chat-script on a line |
| systat Display information about terminal lines |
| tarp TARP (Target ID Resolution Protocol) commands |
| tclquit Quit Tool Command Language shell |
| tclsafe Tool Command Language shell SAFE mode |
| tclsh Tool Command Language shell |
| telnet Open a telnet connection |
| terminal Set terminal line parameters |
| test Test subsystems, memory, and interfaces |
| tms Threat Mitigation Service |
| traceroute Trace route to destination |
| tunnel Open a tunnel connection |
| udptn Open an udptn connection |
| undebug Disable debugging functions (see also ‘debug’) |
| upgrade Upgrade commands |
| verify Verify a file |
| vlan Configure VLAN parameters |
| vtp Configure global VTP state |
| webvpn WebVPN exec command |
| where List active connections |
| which-route Do OSI route table lookup and display results |
| write Write running configuration to memory, network, or terminal |
| x28 Become an X.28 PAD |
| x3 Set X.3 parameters on PAD |
| xconnect Xconnect EXEC commands |
Leave a Reply
You must be logged in to post a comment.